Toyota Tundra Service Manual: FCM Destination Information Unmatched (C1AA1)

Toyota Tundra Service Manual / Engine, Hybrid System / Cruise Control / Forward Recognition Camera System / FCM Destination Information Unmatched (C1AA1)

DESCRIPTION

When the forward recognition camera is replaced with a new one, the new forward recognition camera attempts to store country specification information received from the main body ECU (multiplex network body ECU) and ECM. If the country specification information stored in the forward recognition camera is different from that stored in the main body ECU (multiplex network body ECU) or ECM, DTC C1AA1 is stored.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1AA1

FCM Destination Information Unmatched

3 seconds after the ignition switch is turned to ON, destination information stored in the forward recognition camera and that received from the main body ECU (multiplex network body ECU) or ECM do not match for 5 seconds or more.
  • CAN communication system
  • Forward recognition camera
  • Main body ECU (Multiplex network body ECU)
  • ECM

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
  • If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Learning.

    Click here

HINT:

This DTC is stored when the destination information stored in the forward recognition camera and that stored in the main body ECU (multiplex network body ECU) do not match. If the forward recognition camera or main body ECU (multiplex network body ECU) has been replaced, check if a forward recognition camera or main body ECU (multiplex network body ECU) from another vehicle was used.

PROCEDURE

1.

CHECK FOR DTCs (CAN COMMUNICATION DTC OUTPUT)

HINT:

The forward recognition camera communicates with the main body ECU (multiplex network body ECU) via CAN communication. Confirm that the CAN communication system is functioning normally before proceeding.

(a) Check for DTCs.

Click here

Result

Proceed to

DTC U0142 is not output

A

DTC U0142 is output

B
B

GO TO CAN COMMUNICATION SYSTEM

A

2.

CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)

(a) Clear the DTCs.

Click here

(b) Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.

(c) Check for DTCs.

Click here

Result

Proceed to

DTC C1AA1 is not output

A

DTC C1AA1 is output

B
A

USE SIMULATION METHOD TO CHECK

B

3.

REPLACE FORWARD RECOGNITION CAMERA

(a) Replace the forward recognition camera.

Click here

(b) Perform forward recognition camera axis adjustment.

Click here

NEXT

4.

CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)

(a) Clear the DTCs.

Click here

(b) Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.

(c) Check for DTCs.

Click here

Result

Proceed to

DTC C1AA1 is not output

A

DTC C1AA1 is output

B
A

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)
B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

    Front Camera Module Circuit (C1AA0)

    Vehicle Speed Tolerance Malfunction (C1AA2)

    See More:

    Toyota Tundra Service Manual > Power Window Control System(w/o Jam Protection Function): Driver Side Power Window does not Operate with Power Window Master Switch
    DESCRIPTION If the driver side manual UP/DOWN function does not operate, there may be a malfunction in master switch, driver side motor or harness and connector. WIRING DIAGRAM PROCEDURE 1. INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (a) Remove the front power window regulator motor assem ...

    Toyota Tundra Owners Manual

    Toyota Tundra Service Manual

    © 2025 Copyright www.ttundra.com
    0.0098