Toyota Tundra Service Manual: Vehicle Speed Sensor Circuit (C1AA3)

Toyota Tundra Service Manual / Engine, Hybrid System / Cruise Control / Lane Departure Alert System / Vehicle Speed Sensor Circuit (C1AA3)

DESCRIPTION

The forward recognition camera receives vehicle speed signals from the skid control ECU (brake actuator assembly). If the skid control ECU (brake actuator assembly) receives a vehicle speed sensor malfunction signal, it informs the forward recognition camera via CAN communication, and DTC C1AA3 is stored.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1AA3

Vehicle Speed Sensor Circuit

3 seconds after the ignition switch is turned to ON, a signal from the skid control ECU (brake actuator assembly) indicating a malfunction in a vehicle speed sensor is detected by the forward recognition camera for 5 seconds or more.
  • Vehicle stability control system
  • Skid control ECU (Brake actuator assembly)
  • Forward recognition camera

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
  • If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera learning.

    Click here

  • First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting.

    Click here

PROCEDURE

1.

CHECK DTC OUTPUT (VEHICLE STABILITY CONTROL SYSTEM)

HINT:

If DTC C1AA3 is stored, the vehicle stability control system may be malfunctioning. Check for DTCs related to the vehicle stability control system first.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Check for DTCs.

Click here

Result

Proceed to

Vehicle stability control system DTCs are not output

A

Vehicle stability control system DTCs are output

B
B

GO TO VEHICLE STABILITY CONTROL SYSTEM

A

2.

CHECK DTC OUTPUT

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Chassis / LKA/LDA / Trouble Codes.

(e) Clear the DTCs.

(f) Make sure that the DTC detection conditions are met.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

(g) Check for DTCs.

Result

Proceed to

DTC C1AA3 is output

A

DTC C1AA3 is not output

B
B

USE SIMULATION METHOD TO CHECK

A

3.

REPLACE FORWARD RECOGNITION CAMERA

(a) Replace the forward recognition camera.

Click here

(b) Adjust the forward recognition camera.

Click here

NEXT

4.

CHECK DTC OUTPUT

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Chassis / LKA/LDA / Trouble Codes.

(e) Clear the DTCs.

(f) Make sure that the DTC detection conditions are met.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

(g) Check for DTCs.

Result

Proceed to

DTC C1AA3 is output

A

DTC C1AA3 is not output

B
A

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

B

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)
    Vehicle Speed Tolerance Malfunction (C1AA2)

    Yaw Rate Sensor Circuit (C1AA4,C1AA5)

    See More:

    Toyota Tundra Service Manual > Rear Axle Shaft: Removal
    REMOVAL CAUTION / NOTICE / HINT HINT: Use the same procedures for the LH side and RH side. The procedures listed below are for the LH side. PROCEDURE 1. REMOVE REAR WHEEL LH 2. DRAIN BRAKE FLUID 3. DISCONNECT REAR BRAKE FLEXIBLE HOSE (a) Disconnect the brake tube from the flexible hose with union nu ...

    Toyota Tundra Owners Manual

    Toyota Tundra Service Manual

    © 2026 Copyright www.ttundra.com
    0.0329