Toyota Tundra Service Manual: Installation

INSTALLATION

PROCEDURE

1. INSTALL STEERING COLUMN ASSEMBLY

(a) Install the steering column with the bolt and 2 nuts.

Torque:

21 N·m {214 kgf·cm, 15 ft·lbf}

2. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

(a) Align the matchmarks on the No. 2 steering intermediate shaft and power steering gear.

Text in Illustration

*a

Matchmark

(b) Install the bolt.

Torque:

35 N·m {357 kgf·cm, 26 ft·lbf}

3. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY

(a) Align the matchmarks on the steering intermediate shaft and No. 2 steering intermediate shaft.

Text in Illustration

*a

Matchmark

(b) Install the bolt.

Torque:

35 N·m {357 kgf·cm, 26 ft·lbf}

(c) Align the matchmarks on the steering column and steering intermediate shaft.

Text in Illustration

*a

Matchmark

(d) Install the bolt.

Torque:

35 N·m {357 kgf·cm, 26 ft·lbf}

(e) Install the 3 bolts and nut.

Torque:

5.0 N·m {51 kgf·cm, 44 in·lbf}

4. INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY

(a) Install the No. 3 air duct sub-assembly with the bolt.

Torque:

5.4 N·m {55 kgf·cm, 48 in·lbf}

5. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

6. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH

7. INSTALL INSTRUMENT SIDE PANEL LH

8. INSTALL COWL SIDE TRIM BOARD LH

9. INSTALL FRONT DOOR SCUFF PLATE LH

10. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

(a) Install the combination switch assembly with spiral cable to the steering column assembly with the clamp.

(b) Connect the 5 connectors to the combination switch with spiral cable.

11. INSTALL UPPER STEERING COLUMN COVER

(a) Attach the claw to install the upper steering column cover.

(b) Attach the 4 clips.

12. INSTALL LOWER STEERING COLUMN COVER

(a) Attach the 2 claws to install the column cover.

(b) Install the 2 screws.

13. INSTALL TILT AND TELESCOPIC MANUAL SWITCH

(a) Attach the claw to install the tilt and telescopic switch.

(b) Connect the connector.

14. ADJUST SPIRAL CABLE

15. INSTALL STEERING WHEEL ASSEMBLY

(a) Align the matchmarks on the steering wheel and steering main shaft.

Text in Illustration

*a

Matchmark

(b) Install the steering wheel set nut.

Torque:

50 N·m {510 kgf·cm, 37 ft·lbf}

16. INSPECT STEERING WHEEL CENTER POINT

17. ADJUST SPIRAL CABLE

18. INSTALL STEERING PAD

19. INSTALL LOWER NO. 3 STEERING WHEEL COVER

20. INSTALL LOWER NO. 2 STEERING WHEEL COVER

21. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:

5.4 N·m {55 kgf·cm, 48 in·lbf}

NOTICE:

Some systems need to be initialized after the cable is reconnected (See page ).

22. CHECK SRS WARNING LIGHT

(See page )

    Inspection

    On-vehicle Inspection

    See More:

    Toyota Tundra Service Manual > Audio And Visual System: Poor Sound Quality in All Modes (Low Volume)
    PROCEDURE 1. CHECK AUDIO SETTINGS (a) Set treble, middle and bass to the initial values and check that the sound is normal. OK: The sound returns to normal. OK END (AUDIO SETTINGS ARE DEFECTIVE) NG 2. COMPARE WITH ANOTHER VEHICLE OF SAME MODEL (a) Compare with another vehicle of the same model which ...

    Toyota Tundra Owners Manual

    Toyota Tundra Service Manual

    © 2024 Copyright www.ttundra.com
    0.0357