Toyota Tundra Service Manual: Removal

REMOVAL

PROCEDURE

1. REMOVE RADIATOR GRILLE SUB-ASSEMBLY

Click here

2. REMOVE FRONT END PANEL LH

(a) Put protective tape around the front end panel LH.

Text in Illustration

*1

Protective Tape

(b) Remove the 2 screws and 2 clips.

(c) Detach the 3 claws and remove the front end panel LH.

3. REMOVE FRONT END PANEL RH

HINT:

Use the same procedure described for the LH side.

4. REMOVE FRONT BUMPER COVER

(a) for Steel Type Bumper:

(1) Remove the 2 screws.

HINT:

Use the same procedure for the RH and LH sides.

(b) for Resin Type Bumper:

(1) Remove the 2 screws.

HINT:

Use the same procedure for the RH and LH sides.

(c) Remove the 4 bolts.

Text in Illustration

*1

Screw A

*2

Screw B

*3

Bolt

(d) Remove the 4 screws labeled A and 3 screws labeled B.

(e) Remove the 4 bolts.

Text in Illustration

*A

w/ Intuitive Parking Assist System

(f) w/ Fog Light:

(1) Disconnect the fog light connectors and remove the front bumper cover.

(g) w/ Intuitive Parking Assist System:

(1) Detach the 4 clamps and disconnect the wire harness.

(2) Disconnect the ultrasonic sensor connectors and remove the front bumper cover.

5. REMOVE FRONT FENDER MAIN SEAL LH

(a) Remove the front fender main seal LH.

6. REMOVE FRONT FENDER MAIN SEAL RH

HINT:

Use the same procedure described for the LH side.

7. REMOVE FRONT BUMPER ARM LH

(a) Detach the clamp and disconnect the engine room wire.

(b) Remove the 3 nuts and front bumper arm LH.

8. REMOVE FRONT BUMPER ARM RH

HINT:

Use the same procedure described for the LH side.

9. REMOVE FRONT BUMPER REINFORCEMENT

(a) Remove the 6 nuts and front bumper reinforcement.

10. REMOVE FRONT BUMPER NO. 2 EXTENSION SUB-ASSEMBLY LH

(a) Remove the 4 nuts and front bumper No. 2 extension sub-assembly LH.

11. REMOVE FRONT BUMPER NO. 2 EXTENSION SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.

12. REMOVE FRONT BUMPER SIDE SUPPORT LH

(a) Remove the screw.

(b) Using a screwdriver, turn the clip 90° and remove the clip.

(c) Detach the clip and remove the front bumper side support LH.

13. REMOVE FRONT BUMPER SIDE SUPPORT RH

HINT:

Use the same procedure described for the LH side.

14. REMOVE FRONT BUMPER CENTER UPPER RETAINER

(a) Remove the 6 nuts and front bumper center upper retainer.

15. REMOVE FRONT BUMPER END RETAINER LH

(a) Remove the 3 nuts and front bumper end retainer LH.

16. REMOVE FRONT BUMPER END RETAINER RH

HINT:

Use the same procedure described for the LH side.

    Reassembly

    Front Door Belt Moulding(for Crewmax)

    See More:

    Toyota Tundra Service Manual > Sfi System: Engine Stall History (P1603,P1605)
    DESCRIPTION P1603 After starting the engine, this DTC is stored when the engine stops without the ignition switch being operated. Using the Techstream, the conditions present when the DTC was stored can be confirmed by referring to the freeze frame data. Freeze frame data records engine conditions w ...

    Toyota Tundra Owners Manual

    Toyota Tundra Service Manual

    © 2024 Copyright www.ttundra.com
    0.0349