Toyota Tundra Service Manual: Installation

INSTALLATION

CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page ).

PROCEDURE

1. INSTALL NO. 1 INSTRUMENT PANEL CLIP

2. INSTALL NO. 3 INSTRUMENT PANEL STAY

3. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY

(a) Set the instrument panel sub-assembly and attach the 5 claws.

(b) Install the 2 nuts <C> and 3 bolts <B>.

(c) Install the 2 bolts <G>.

Torque:

20 N·m {204 kgf·cm, 15 ft·lbf}

Text in Illustration

*1

Bolt <G>

*2

Bolt <B>

*3

Nut <C>

-

-

(d) for Automatic Air Conditioning System:

Attach the 2 claws to connect the cooler thermistor.

(e) Connect each connector and attach each wire harness clamp.

Text in Illustration

*A

w/ Automatic Light Control System

*2

w/ Front Center Speaker

*3

for Automatic Air Conditioning System

-

-

4. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY LH

5. INSTALL INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

6. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY RH

7. INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

8. INSTALL FRONT PILLAR GARNISH LH

9. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

10. INSTALL FRONT PILLAR GARNISH RH

11. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.

12. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

13. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET

14. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL WITH AIR CONDITIONING CONTROL ASSEMBLY

15. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

16. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY RH

17. INSTALL INSTRUMENT SIDE PANEL RH

18. INSTALL NO. 4 INSTRUMENT REGISTER SUB-ASSEMBLY

19. INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

20. INSTALL LOWER INSTRUMENT PANEL

21. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

22. INSTALL COMBINATION METER ASSEMBLY

23. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

(a) Attach the 6 clips to install the instrument cluster finish panel assembly.

(b) Install the 2 clips.

24. INSTALL INSTRUMENT CLUSTER FINISH PANEL ORNAMENT

(a) Attach the 3 clips and claw to install the instrument cluster finish panel ornament.

25. INSTALL NO. 2 SWITCH HOLE BASE

(a) Connect each connector.

(b) Attach the 4 clips to install the No. 2 switch hole base.

26. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

27. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

28. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LH

29. INSTALL COWL SIDE TRIM BOARD LH

30. INSTALL FRONT DOOR SCUFF PLATE LH

31. INSTALL COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure described for the LH side.

32. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.

33. INSTALL FRONT CONSOLE BOX

(a) Install the front console box with the 5 screws <E>.

(b) Install the 2 clips and attach the connector.

34. INSTALL REAR CONSOLE BOX ASSEMBLY

(a) Install the rear console box assembly with the 2 screws <E> and 4 bolts <B>.

(b) Connect the 2 connectors.

35. INSTALL CONSOLE BOX CARPET

(a) Install the console box carpet.

36. INSTALL REAR CONSOLE END PANEL SUB-ASSEMBLY

(a) w/ Power Outlet Socket:

Attach the 2 wire harness clamps and connect the connector.

(b) Attach the 7 clips to install the rear console end panel sub-assembly.

37. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY

(a) Attach the 12 clips to install the upper console panel sub-assembly.

38. INSTALL UPPER REAR CONSOLE PANEL SUB-ASSEMBLY

(a) Attach the 6 clips to install the upper rear console panel sub-assembly.

39. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

(a) Twist the shift lever knob sub-assembly in the direction indicated by the arrow to install it.

HINT:

  • Tighten the shift lever knob sub-assembly until there is no rotational free-play.
  • If the leather portion of the knob is not facing forward, tighten the knob further until the leather portion faces forward.
Text in Illustration

*a

Leather Portion

40. INSTALL INSTRUMENT SIDE PANEL LH

41. INSTALL NO. 1 INSTRUMENT PANEL REGISTER SUB-ASSEMBLY

42. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page ).

43. RESTORE AUTOAWAY/RETURN FUNCTION (for Power Tilt and Power Telescopic Steering Column)

(a) Restore the Autoaway/Return function setting to the previous condition by changing the customize parameter (See page ).

44. CHECK SRS WARNING LIGHT

(See page )

    Disassembly

    Reassembly

    See More:

    Toyota Tundra Service Manual > Instrument Panel Safety Pad(for Floor Shift Type): Installation
    INSTALLATION CAUTION / NOTICE / HINT HINT: A bolt without a torque specification is shown in the standard bolt chart (See page ). PROCEDURE 1. INSTALL NO. 1 INSTRUMENT PANEL CLIP 2. INSTALL NO. 3 INSTRUMENT PANEL STAY 3. INSTALL INSTRUMENT PANEL SUB-ASSEMBLY (a) Set the instrument panel sub-assembly ...

    Toyota Tundra Owners Manual

    Toyota Tundra Service Manual

    © 2022 Copyright www.ttundra.com
    0.0089