1. DATA LIST
Using the Techstream to read the Data List allows the values or states of switches,
sensors, actuators and other items to be read without removing any parts. This non-intrusive
inspection can be very useful because intermittent conditions or signals may be
discovered before parts or wiring is disturbed. Reading the Data List information
early in troubleshooting is one way to save diagnostic time.
In the table below, the values listed under "Normal Condition" are reference
values. Do not depend solely on these reference values when deciding whether a part
is faulty or not.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Driver Seat / Data List.
(e) Read the Data List according to the display on the Techstream.
Driver Seat
|
Tester Display
|
Measurement Item/Range
|
Normal Condition
|
Diagnostic Note
|
|
Reclining Rear
|
Reclining switch signal (Rearward) / ON or OFF
|
ON: Reclining switch (Rearward) on
OFF: Reclining switch (Rearward) off
|
-
|
|
Reclining Front
|
Reclining switch signal (Forward) / ON or OFF
|
ON: Reclining switch (Forward) on
OFF: Reclining switch (Forward) off
|
-
|
|
Front Vertical Down
|
Front vertical switch signal (Downward) / ON or OFF
|
ON: Front vertical switch (Downward) on
OFF: Front vertical switch (Downward) off
|
-
|
|
Front Vertical Up
|
Front vertical switch signal (Upward) / ON or OFF
|
ON: Front vertical switch (Upward) on
OFF: Front vertical switch (Upward) off
|
-
|
|
Lifter Switch Down
|
Lifter switch signal (Downward) / ON or OFF
|
ON: Lifter switch (Downward) on
OFF: Lifter switch (Downward) off
|
-
|
|
Lifter Switch Up
|
Lifter switch signal (Upward) / ON or OFF
|
ON: Lifter switch (Upward) on
OFF: Lifter switch (Upward) off
|
-
|
|
Slide Rear
|
Sliding switch signal (Rearward) / ON or OFF
|
ON: Sliding switch (Rearward) on
OFF: Sliding switch (Rearward) off
|
-
|
|
Slide Front
|
Sliding switch signal (Forward) / ON or OFF
|
ON: Sliding switch (Forward) on
OFF: Sliding switch (Forward) off
|
-
|
|
SET Switch
|
Seat memory switch SET signal / ON or OFF
|
ON: Seat memory switch SET on
OFF: Seat memory switch SET off
|
-
|
|
M1 Switch
|
Seat memory switch M1 signal / ON or OFF
|
ON: Seat memory switch M1 on
OFF: Seat memory switch M1 off
|
-
|
|
M2 Switch
|
Seat memory switch M2 signal / ON or OFF
|
ON: Seat memory switch M2 on
OFF: Seat memory switch M2 off
|
-
|
|
Seat Memory No1
|
Seat position memorized with M1 switch / Mem or Not Mem
|
Mem: Memorized
Not Mem: Not memorized
|
-
|
|
Seat Memory No2
|
Seat position memorized with M2 switch / Mem or Not Mem
|
Mem: Memorized
Not Mem: Not memorized
|
-
|
|
Ignition Switch
|
Communication state of ignition switch signal / ON or OFF
|
ON: Ignition switch ON signal received
OFF: Ignition switch off signal not received
|
-
|
|
Key Switch
|
Ignition switch status / ON or OFF
|
ON: Ignition switch ON
OFF: Ignition switch off
|
"OFF" is also displayed for this item when the ignition switch is ACC
|
|
Key Code Confirm
|
Recognition code is registered / ON or OFF
|
ON: One more recognition codes registered
OFF: No recognition code registered
|
-
|
|
D-Door Courtesy
|
Front door courtesy light switch assembly signal / ON or OFF
|
ON: Driver door open
OFF: Driver door closed
|
-
|
|
P Switch
|
Park state signal / ON or OFF
|
ON: Shift lever in P
OFF: Shift lever in a position other than P
|
-
|
|
Parking Brake SW
|
Parking brake switch status / ON or OFF
|
ON: Parking brake applied
OFF: Parking brake released
|
-
|
|
Vehicle Speed
|
Vehicle speed data / Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
|
Actual vehicle speed
|
-
|
|
Power Voltage
|
Power supply for position control ECU and switch assembly / Min: 0 V,
Max: 19.89 V
|
Within range from 11 to 14 V
|
-
|
|
Slide Position
|
Seat sliding position / Min: 0000, Max: 65535
|
Within range of 0 to 65535
(Seat position displayed)
|
-
|
|
Reclining Position
|
Seat reclining position / Min: 0000, Max: 65535
|
Within range of 0 to 65535
(Seat position displayed)
|
-
|
|
Front Vertical Position
|
Seat front vertical position / Min: 0000, Max: 65535
|
Within range of 0 to 65535
(Seat position displayed)
|
-
|
|
Lifter Position
|
Seat lifter position / Min: 0000, Max: 65535
|
Within range of 0 to 65535
(Seat position displayed)
|
-
|
|
Slide Pos Mem No1
|
Seat sliding position memorized with M1 switch / Min: 0000, Max: 65535
|
Within range of 0 to 65535
(Seat position displayed)
|
-
|
|
Reclining Pos Mem No1
|
Seat reclining position memorized with M1 switch / Min: 0000, Max: 65535
|
Within range of 0 to 65535
(Seat position displayed)
|
-
|
|
Frnt Vrtcl Pos Mem No1
|
Front vertical position memorized with M1 switch / Min: 0000, Max: 65535
|
Within range of 0 to 65535
(Seat position displayed)
|
-
|
|
Lifter Pos Mem No1
|
Lifter position memorized with M1 switch / Min: 0000, Max: 65535
|
Within range of 0 to 65535
(Seat position displayed)
|
-
|
|
Slide Pos Mem No2
|
Seat sliding position memorized with M2 switch / Min: 0000, Max: 65535
|
Within range of 0 to 65535
(Seat position displayed)
|
-
|
|
Reclining Pos Mem No2
|
Seat reclining position memorized with M2 switch / Min: 0000, Max: 65535
|
Within range of 0 to 65535
(Seat position displayed)
|
-
|
|
Frnt Vrtcl Pos Mem No2
|
Front vertical position memorized with M2 switch / Min: 0000, Max: 65535
|
Within range of 0 to 65535
(Seat position displayed)
|
-
|
|
Lifter Pos Mem No2
|
Lifter position memorized with M2 switch / Min: 0000, Max: 65535
|
Within range of 0 to 65535
(Seat position displayed)
|
-
|
|
Memory No1
|
Seat memory switch M1 signal / Mem or Not Mem
|
Mem: Memorized
Not Mem: Not memorized
|
-
|
|
Memory No2
|
Seat memory switch M2 signal / Mem or Not Mem
|
Mem: Memorized
Not Mem: Not memorized
|
-
|
|
Motor Status
|
State of slide motor control / STANDBY, MOVING, LOCK
|
STANDBY: Slide motor idle
MOVING: Slide motor moving
LOCK: Slide motor locked
|
-
|
|
Slide Position Rear Limit
|
Seat sliding position / Min: 0000, Max: 65535
|
Within range of 0 to 65535
|
-
|
|
Return Move
|
Return destination / AVAIL or NOT AVL
|
AVAIL: Return destination set
NOT AVL: Return destination not set
|
-
|
|
Return & Away Function
|
Power easy access system status / AVAIL or NOT AVL
|
AVAIL: Power easy access system functioning
NOT AVL: Power easy access system not functioning
|
-
|
|
Driver Seat Buckle SW
|
Status of the driver seat belt / ON or OFF
|
ON: Tongue plate is engaged
OFF: Tongue plate is not engaged
|
-
|
|
Return Position
|
Return position / Min: 0000, Max: 65535
|
Within range of 0 to 65535
|
-
|
|
Seat Travel Distance
|
Setting of the customized item "Seat Travel Distance" / OFF, Short, Normal
|
Customized value displayed
|
-
|
|
Number of Trouble Codes
|
Number of trouble codes / Min.: 0 ,or Max.: 255
|
Number of DTCs will be displayed
|
-
|
(f) Enter the following menus: Body Electrical / Main Body / Data List.
(g) Read the Data List according to the display on the Techstream.
Main Body
2. ACTIVE TEST
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and
other items to be operated without removing any parts. This non-intrusive functional
inspection can be very useful because intermittent operation may be discovered before
parts or wiring is disturbed. Performing Active Tests early in troubleshooting is
one way to save diagnostic time. Data List information can be displayed while performing
Active Tests.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Driver Seat / Active Test.
(e) Perform the Active Test according to the display on the Techstream.
Driver Seat
