Toyota Tundra Service Manual: Reassembly

REASSEMBLY

PROCEDURE

1. INSTALL STUD BOLT

(a) Using E7 and E8 "TORX" socket wrenches, install the stud bolts.

Torque:

for stud bolts A, B, C, D :

9.0 N·m {92 kgf·cm, 80 in·lbf}

2. INSTALL NO. 2 STRAIGHT SCREW PLUG

(a) Using a 14 mm hexagon wrench, install 2 new gaskets and the 2 straight screw plugs.

Torque:

85 N·m {867 kgf·cm, 63 ft·lbf}

3. INSTALL NO. 1 STRAIGHT SCREW PLUG

(a) Using a 10 mm hexagon wrench, install 6 new gaskets and the 6 straight screw plugs.

Torque:

44 N·m {449 kgf·cm, 32 ft·lbf}

4. INSTALL VALVE SPRING SEAT

(a) Install the valve spring seats to the cylinder head.

5. INSTALL VALVE STEM OIL SEAL

(a) Apply a light coat of engine oil to new oil seals.

NOTICE:

Pay attention when installing the intake and exhaust oil seals. For example, installing the intake oil seal into the exhaust side or installing the exhaust oil seal into the intake side can cause installation problems later.

HINT:

  • for Intake Side

    The intake side valve stem oil seals is gray or black.

  • for Exhaust Side

    The exhaust side valve stem oil seals is black or gray.

(b) Using SST, push in the oil seals.

SST: 09201-41020

NOTICE:

Failure to use SST will cause the seal to be damaged or improperly seated.

6. INSTALL INTAKE VALVE

(a) Apply plenty of engine oil to the tip area of the intake valve shown in the illustration.

(b) Install the valve, compression spring and spring retainer to the cylinder head.

NOTICE:

  • Install the same parts in the same combination to their original locations.
  • Install the inner compression spring to the wide end of the cylinder head sub-assembly.

(c) Using SST and wooden blocks, compress the spring and install the valve spring retainer locks.

SST: 09202-70020

09202-01010

09202-01020

SST: 09202-00021

(d) Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

  • Do not damage the valve stem tip.
  • Be careful not to damage the retainer.

7. INSTALL EXHAUST VALVE

(a) Apply plenty of engine oil to the tip area of the exhaust valve shown in the illustration.

(b) Install the valve, compression spring and spring retainer to the cylinder head.

NOTICE:

  • Install the same parts in the same combination to their original locations.
  • Install the inner compression spring to the wide end of the cylinder head sub-assembly.

(c) Using SST and wooden blocks, compress the spring and install the valve spring retainer locks.

SST: 09202-70020

09202-01010

09202-01020

SST: 09202-00021

(d) Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:

  • Do not damage the valve stem tip.
  • Be careful not to damage the retainer.
    Precaution

    Repair

    See More:

    Toyota Tundra Service Manual > Driver Side Knee Airbag Assembly: On-vehicle Inspection
    ON-VEHICLE INSPECTION PROCEDURE 1. CHECK LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (VEHICLE NOT INVOLVED IN COLLISION) (a) Perform a diagnostic system check (See page ). (b) With the lower No. 1 instrument panel airbag installed on the vehicle, perform a visual check. If there are any defects as ...

    Toyota Tundra Owners Manual

    Toyota Tundra Service Manual

    © 2024 Copyright www.ttundra.com
    0.0169