Toyota Tundra Service Manual: FCM Destination Information Uninitialized (C1AAA)

Toyota Tundra Service Manual / Engine, Hybrid System / Cruise Control / Forward Recognition Camera System / FCM Destination Information Uninitialized (C1AAA)

DESCRIPTION

When the forward recognition camera is replaced with a new one, the new forward recognition camera attempts to store the country specification information received from the main body ECU (multiplex network body ECU). If the forward recognition camera cannot store the country specification information, DTC C1AAA is stored.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1AAA

FCM Destination Information Uninitialized

After the ignition switch is turned to ON for 3 seconds or more, when the vehicle is being driven at a speed of 1 km/h (1 mph) or more, the forward recognition camera cannot store the vehicle specification information for 5 seconds or more.
  • CAN communication system
  • Main body ECU (Multiplex network body ECU)
  • Forward recognition camera

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
  • If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Learning.

    Click here

HINT:

This DTC is stored when the forward recognition camera cannot store the country specification information received from the main body ECU (multiplex network body ECU). If the forward recognition camera or main body ECU (multiplex network body ECU) has been replaced, check if a forward recognition camera or main body ECU (multiplex network body ECU) from another vehicle was used.

PROCEDURE

1.

CHECK FOR DTCs (CAN COMMUNICATION DTC OUTPUT)

HINT:

The forward recognition camera communicates with the main body ECU (multiplex network body ECU) via CAN communication. Confirm that the CAN communication system is functioning normally before proceeding.

(a) Check for DTCs.

Click here

Result

Proceed to

DTC U0142 is not output

A

DTC U0142 is output

B
B

GO TO CAN COMMUNICATION SYSTEM

A

2.

CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)

(a) Clear the DTCs.

Click here

(b) Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.

(c) Check for DTCs.

Click here

Result

Proceed to

DTC C1AAA is not output

A

DTC C1AAA is output

B
A

USE SIMULATION METHOD TO CHECK

B

3.

REPLACE FORWARD RECOGNITION CAMERA

(a) Replace the forward recognition camera.

Click here

(b) Perform forward recognition camera axis adjustment.

Click here

NEXT

4.

CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)

(a) Clear the DTCs.

Click here

(b) Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.

(c) Check for DTCs.

Click here

Result

Proceed to

DTC C1AAA is not output

A

DTC C1AAA is output

B
A

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)
B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

    Front Camera Module Incorrect Axial Gap (C1AA8,C1AA9)

    Heater Circuit (C1AAE)

    See More:

    Toyota Tundra Service Manual > Automatic Transmission System: Shift Solenoid "A" Control Circuit Low (Shift Solenoid Valve S1) (P0973,P0974)
    DESCRIPTION Shifting from 1st to 6th is performed in combination with ON and OFF operation of the shift solenoid valves SL1, SL2, S1, S2, S3, S4 and SR, which are controlled by the ECM. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shif ...

    Toyota Tundra Owners Manual

    Toyota Tundra Service Manual

    © 2026 Copyright www.ttundra.com
    0.0352