Toyota Tundra Service Manual: Voice Recognition Microphone Disconnected (B1579)

Toyota Tundra Service Manual / Audio, Visual, Telematics / Audio / Video / Audio And Visual System / Voice Recognition Microphone Disconnected (B1579)

DESCRIPTION

The radio and display receiver assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

This DTC is stored when a microphone connection detection signal line is disconnected.

DTC Code

DTC Detection Condition

Trouble Area

B1579

Telephone microphone signal is lost.

  • Radio and display receiver assembly
  • Telephone microphone assembly
  • Harness or connector

WIRING DIAGRAM

PROCEDURE

1.

CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)

(a) Disconnect the J139 radio and display receiver assembly connector.

(b) Disconnect the W11 telephone microphone assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

J139-4 (MACC) - W11-1 (MACC)

Always

Below 1 Ω

J139-5 (MIN+) - W11-2 (MIC+)

Always

Below 1 Ω

J139-19 (MIN-) - W11-4 (MIC-)

Always

Below 1 Ω

J139-6 (SNS2) - W11-3 (SNS2)

Always

Below 1 Ω

J139-4 (MACC) - Body ground

Always

10 kΩ or higher

J139-5 (MIN+) - Body ground

Always

10 kΩ or higher

J139-19 (MIN-) - Body ground

Always

10 kΩ or higher

J139-18 (SGND) - Body ground

Always

10 kΩ or higher

J139-6 (SNS2) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

2.

CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

(a) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

J139-18 (SGND) - Body ground

Always

Below 1 Ω

J139-19 (MIN-) - Body ground

Always

Below 1 Ω

*a

Component with harness connected

(Radio and Display Receiver Assembly)

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

J139-4 (MACC) - Body ground

Ignition switch ACC

4 to 6 V

Result

Result

Proceed to

OK

A

NG (for Column Shift Type)

B

NG (for Floor Shift Type)

C

B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

C

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

A

3.

CHECK TELEPHONE MICROPHONE ASSEMBLY

(a) Replace the telephone microphone assembly with a known good one (See page ).

(b) Clear the DTCs (See page ).

(c) Check for DTCs (See page ).

OK:

No DTCs are output.

Result

Result

Proceed to

OK

A

NG (for Column Shift Type)

B

NG (for Floor Shift Type)

C

A

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

B

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

C

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

    HD Radio Tuner Malfunction (B1551,B15A0,B15B0,B15B3-B15B5,B15B7)

    USB Device Malfunction (B1585)

    See More:

    Toyota Tundra Service Manual > Front Drive Shaft Assembly(for 4wd): Removal
    REMOVAL CAUTION / NOTICE / HINT HINT: Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side. PROCEDURE 1. REMOVE FRONT WHEEL 2. REMOVE NO. 1 ENGINE UNDER COVER 3. DRAIN DIFFERENTIAL OIL 4. DISCONNECT FRONT SPEED SENSOR LH (a) Disconnect the front speed ...

    Toyota Tundra Owners Manual

    Toyota Tundra Service Manual

    © 2021 Copyright www.ttundra.com
    0.0175