Toyota Tundra Service Manual: Disassembly

DISASSEMBLY

PROCEDURE

1. REMOVE PROPELLER SHAFT UNIVERSAL JOINT SPIDER BEARING

(a) Place matchmarks on the propeller shaft yoke and universal joint yoke.

Text in Illustration

*a

Matchmark

(b) Using a brass bar and hammer, slightly tap in the 4 spider bearings.

(c) Using needle-nose pliers, remove the 4 snap rings from the grooves.

(d) Using a screwdriver, remove the 4 slingers of the spider bearing.

(e) Clamp the propeller shaft in a vise between aluminum plates.

(f) Using SST, press in spider bearing B until spider bearing A can be clamped in a vise.

SST: 09950-40011

09951-04010

09952-04010

09953-04030

09954-04010

09957-04010

09958-04011

SST: 09950-60010

09951-00290

SST: 09955-04100

Text in Illustration

*a

Spider Bearing A

*b

Spider Bearing B

*c

Turn

*d

Hold

HINT:

Make sure the claws of SST are securely attached to the universal joint yoke.

(g) Clamp the protruding universal joint spider bearing in a vise.

(h) Using a brass bar and hammer, tap the universal joint yoke to remove the universal joint spider bearing.

Text in Illustration

*a

Hammering Point

NOTICE:

Do not tap the intermediate shaft tube.

HINT:

Use the same removal procedure for the universal joint spider bearing on the opposite side.

(i) Disconnect the intermediate shaft from the propeller shaft.

(j) Using SST, pull out the universal joint spider bearing from the propeller shaft yoke.

SST: 09331-60010

SST: 09950-40011

09951-04010

09952-04010

09953-04020

09954-04010

09957-04010

09958-04011

SST: 09955-04100

Text in Illustration

*a

Spider Bearing

*b

Turn

*c

Hold

NOTICE:

Pull out the spider bearing until the SST claws contact the propeller shaft yoke.

(k) Clamp the protruding universal joint spider bearing in a vise.

(l) Using a brass bar and hammer, tap the propeller shaft yoke to remove the universal joint spider bearing.

Text in Illustration

*a

Hammering Point

NOTICE:

Do not tap the propeller shaft tube.

HINT:

Use the same removal procedure for the universal joint spider bearing on the opposite side.

(m) Remove the spider from the propeller shaft.

2. REMOVE NO. 1 CENTER SUPPORT BEARING ASSEMBLY

(a) Fix the center support bearing in a vise.

(b) Using a chisel and hammer, loosen the staked part of the lock nut. Then remove the lock nut.

(c) Place matchmarks on the joint yoke and shaft.

Text in Illustration

*a

Matchmark

(d) Using a brass bar and hammer, tap the end of the intermediate shaft to remove the joint yoke, washer and center support bearing from the intermediate shaft.

3. REMOVE PROPELLER SHAFT UNIVERSAL JOINT SPIDER BEARING

HINT:

Use the same removal procedure for both the sleeve yoke side and flange yoke side universal joint spider bearings.

(a) Place matchmarks on the flange yoke and shaft, and the sleeve yoke and shaft.

Text in Illustration

*a

for Sleeve Yoke Side

*b

for Flange Yoke Side

*c

Matchmark

(b) Using a brass bar and hammer, slightly tap in the spider bearing.

(c) Using needle-nose pliers, remove the snap ring from the grooves.

HINT:

Remove the snap ring on the opposite side using the same procedure.

(d) Using a screwdriver, remove the 4 slingers of the spider bearing.

(e) Clamp the shaft in a vise between aluminum plates.

(f) Using SST, pull out the universal joint spider bearing from the shaft.

SST: 09331-60010

SST: 09950-40011

09951-04010

09952-04010

09953-04020

09954-04010

09957-04010

09958-04011

SST: 09955-04100

Text in Illustration

*a

Spider Bearing

*b

Turn

*c

Hold

NOTICE:

Pull out the spider bearing until the SST claws contact the shaft's universal joint yoke.

(g) Clamp the protruding universal joint spider bearing in a vise.

(h) Using a brass bar and hammer, tap the shaft yoke to remove the universal joint spider bearing.

Text in Illustration

*a

Hammering Point

NOTICE:

Do not tap the shaft tube.

HINT:

Use the same removal procedure for the universal joint spider bearing on the opposite side.

(i) Using SST, pull out the universal joint spider bearing from the sleeve yoke.

SST: 09331-60010

SST: 09950-40011

09951-04010

09952-04010

09953-04020

09954-04010

09957-04010

09958-04011

SST: 09955-04100

Text in Illustration

*a

Spider Bearing

*b

Turn

*c

Hold

NOTICE:

Pull out the spider bearing until the SST claws contact the sleeve yoke.

(j) Clamp the protruding universal joint spider bearing in a vise.

(k) Using a brass bar and hammer, tap the sleeve yoke to remove the universal joint spider bearing.

Text in Illustration

*a

Hammering Point

HINT:

Use the same removal procedure for the universal joint spider bearing on the opposite side.

(l) Remove the spider from the sleeve yoke.

    Components

    Inspection

    See More:

    Toyota Tundra Service Manual > Dynamic Radar Cruise Control System: How To Proceed With Troubleshooting
    CAUTION / NOTICE / HINT HINT: Perform the following procedure to troubleshoot the dynamic radar cruise control system. *: Use the Techstream. PROCEDURE 1. VEHICLE BROUGHT TO WORKSHOP NEXT 2. INSPECT BATTERY VOLTAGE (a) Measure the battery voltage with the ignition switch off. Standard Voltage: 11 to ...

    Toyota Tundra Owners Manual

    Toyota Tundra Service Manual

    © 2021 Copyright www.ttundra.com
    0.0224