Toyota Tundra Service Manual: Air Mix Damper Control Servo Motor Circuit (Passenger Side) (B1441/41)

Toyota Tundra Service Manual / Vehicle Interior / Air Conditioning / Air Conditioning System(for Manual Air Conditioning System) / Air Mix Damper Control Servo Motor Circuit (Passenger Side) (B1441/41)

DESCRIPTION

The No. 1 damper servo sub-assembly (air mix servo motor) sends pulse signals to inform the air conditioning amplifier of the damper position. The air conditioning amplifier activates the motor (normal, reverse) based on the signals to move the No. 1 damper servo sub-assembly (air mix servo motor) to any position. As a result the amount of air that has passed through the evaporator and is now passing through the heater core is adjusted, and the temperature of the air blowing toward the driver side is controlled.

HINT:

Confirm that no mechanical problem is present because this diagnostic trouble code can be output when either a damper link or damper is mechanically locked.

DTC Code

DTC Detection Condition

Trouble Area

B1441/41

Air mix damper position sensor value does not change even if air conditioning amplifier operates No. 1 damper servo sub-assembly (air mix servo motor)

  • No. 1 damper servo sub-assembly (air mix servo motor)
  • Air conditioning harness
  • Air conditioning amplifier

WIRING DIAGRAM

PROCEDURE

1.

READ VALUE USING TECHSTREAM (AIR MIX SERVO MOTOR TARGET PULSE)

(a) Use the Data List to check if the servo motor is functioning properly.

Air Conditioner

Tester Display

Measurement Item / Range

Normal Condition

Diagnostic Note

Air Mix Servo Targ Pulse (D)

No. 1 damper servo sub-assembly (air mix servo motor) target pulse /

Min.: 0, Max.: 255

MAX. COLD: 5 (pulse)

MAX. HOT: 104 (pulse)

-

OK:

The display is as specified in the normal condition.

Result

Result

Proceed to

OK (Checking from the DTC)

A

OK (Checking from the PROBLEM SYMPTOMS TABLE)

B

NG

C

B

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

C

REPLACE AIR CONDITIONING AMPLIFIER

A

2.

REPLACE NO. 1 DAMPER SERVO SUB-ASSEMBLY (AIR MIX SERVO MOTOR)

(a) Temporarily replace the No. 1 damper servo sub-assembly (air mix servo motor) with a new one (see page ).

HINT:

Since the servo motor cannot be inspected while it is removed from the vehicle, replace the servo motor with a new one and check that the condition returns to normal.

NEXT

3.

CHECK FOR DTC

(a) Clear the DTC (see page ).

(b) Check for DTC (see page ).

OK:

DTC is not output.

OK

END (NO. 1 DAMPER SERVO SUB-ASSEMBLY [AIR MIX SERVO MOTOR] IS DEFECTIVE)

NG

4.

REPLACE AIR CONDITIONING HARNESS

(a) Replace the air conditioning harness.

NEXT

5.

CHECK FOR DTC

(a) Clear the DTC (see page ).

(b) Check for DTC again (see page ).

OK:

DTC is not output.

OK

END (AIR CONDITIONING HARNESS IS DEFECTIVE)

NG

REPLACE AIR CONDITIONING AMPLIFIER

    Pressure Sensor Circuit (B1423/23)

    Air Inlet Damper Control Servo Motor Circuit (B1442/42)

    See More:

    Toyota Tundra Service Manual > Differential Carrier Assembly(for 3ur-fe, 3ur-fbe): Installation
    INSTALLATION PROCEDURE 1. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY (a) Clean the contact surfaces of the rear differential carrier and rear axle housing. (b) Install a new gasket and the differential carrier with the 10 washers and 10 nuts. Torque: 72 N·m {734 kgf·cm, 53 ft·lbf} NOTICE: Be care ...

    Toyota Tundra Owners Manual

    Toyota Tundra Service Manual

    © 2021 Copyright www.ttundra.com
    0.0198