Toyota Tundra Service Manual: Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn the Techstream on.

(e) Enter the following menus:

(1) Body Electrical / Main Body / Data List.

(2) Body Electrical / Combination Meter / Data List.

(f) Read the Data List according to the display on the Techstream.

Main Body

Tester Display

Measurement Item / Range

Normal Condition

Diagnostic Note

ACC SW

Ignition switch signal / OFF or ON

OFF: Ignition switch off

ON: Ignition switch ACC

"ON" is also displayed for this item when the ignition switch is ON.

IG SW

Ignition switch signal / OFF or ON

OFF: Ignition switch off

ON: Ignition switch ON

"OFF" is also displayed for this item when the ignition switch is ACC.

Parking Brake SW

Parking brake switch assembly signal / OFF or ON

OFF: Parking brake switch assembly off

ON: Parking brake switch assembly on

-

FR Door Lock Pos

Front door RH unlock detection switch signal / LOCK or UNLOCK

LOCK: Front door RH locked

UNLOCK: Front door RH unlocked

-

FR Door Courtesy SW

Front door courtesy light switch assembly RH signal / OFF or ON

OFF: Front door RH closed

ON: Front door RH open

-

FL Door Lock Pos

Front door LH unlock detection switch signal / LOCK or UNLOCK

LOCK: Front door LH locked

UNLOCK: Front door LH unlocked

-

FL Door Courtesy SW

Front door courtesy light switch assembly LH signal / OFF or ON

OFF: Front door LH closed

ON: Front door LH open

-

RR Door Courtesy SW

Rear door courtesy light switch assembly RH signal / OFF or ON

OFF: Rear door RH closed

ON: Rear door RH open

-

RR-Door Lock Pos SW

Rear door unlock detection switch LH and RH signal / OFF or ON

OFF: LH and RH side rear door locked

ON: LH or RH side rear door unlocked

-

RL Door Courtesy SW

Rear door courtesy light switch assembly LH signal / OFF or ON

OFF: Rear door LH closed

ON: Rear door LH open

-

RL-Door Lock Pos SW

Rear door unlock detection switch LH and RH signal / OFF or ON

OFF: LH and RH side rear door locked

ON: LH or RH side rear door unlocked

-

Deck light switch assembly

Deck light switch assembly signal / OFF or ON

OFF: Deck light switch assembly off

ON: Deck light switch assembly on

-

Dimmer SW

Headlight dimmer switch high position signal / OFF or ON

OFF: Headlight dimmer switch not in high position

ON: Headlight dimmer switch in high position

-

Passing Light SW

Headlight dimmer switch high flash position (pass) signal / OFF or ON

OFF: Headlight dimmer switch not in high flash position

ON: Headlight dimmer switch in high flash position

-

Front Fog Light SW

Fog light switch signal / OFF or ON

OFF: Fog light switch off

ON: Fog light switch in front position

w/ Fog Light

Auto Light SW

Light control switch Auto position signal / OFF or ON

OFF: Light control switch not in Auto position

ON: Light control switch in Auto position

-

Head Light SW (Tail)

Light control switch tail position signal / OFF or ON

OFF: Light control switch in neither tail nor head position

ON: Light control switch in tail or head position

-

Head Light SW (Head)

Light control switch head position signal / OFF or ON

OFF: Light control switch not in head position

ON: Light control switch in head position

-

Auto High Beam Main Switch

Auto high beam switch signal / OFF or ON

OFF: Auto high beam switch off

ON: Auto high beam switch on

w/ Automatic High Beam System

AUTO Light Status

AUTO headlight status / Not AUTO or AUTO

Current control status

-

Light Sensor Connection Status

Connection status to automatic light control sensor / OFF or ON

OFF: Not Connected

ON: Connected

-

Insolation Amount of Solar Sensor RH

Light control sensor RH condition / Min.: 0, Max.: 51100 or Sensor Fail

Condition can be displayed

Although the item is displayed on the Techstream, it is not applicable to the vehicle.

Insolation Amount of Solar Sensor LH

Light control sensor LH condition / Min.: 0, Max.: 51100 or Sensor Fail

Condition can be displayed

Although the item is displayed on the Techstream, it is not applicable to the vehicle.

Light Sensor Illuminance

Light control sensor illuminance / 0 to 8191 lx

Value is output according to ambient light level

-

Auto H Beam STS0

Automatic high beam sensor state past 0 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err

Condition can be displayed*

w/ Automatic High Beam System

Auto H Beam STS1

Automatic high beam sensor state past 1 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err

Condition can be displayed*

  • w/ Automatic High Beam System
  • Although the item is displayed on the Techstream, it is not applicable to the vehicle.

Auto H Beam STS2

Automatic high beam sensor state past 2 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err

Condition can be displayed*

  • w/ Automatic High Beam System
  • Although the item is displayed on the Techstream, it is not applicable to the vehicle.

Auto H Beam STS3

Automatic high beam sensor state past 3 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err

Condition can be displayed*

  • w/ Automatic High Beam System
  • Although the item is displayed on the Techstream, it is not applicable to the vehicle.

Auto H Beam STS4

Automatic high beam sensor state past 4 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err

Condition can be displayed*

  • w/ Automatic High Beam System
  • Although the item is displayed on the Techstream, it is not applicable to the vehicle.

Auto H Beam STS5

Automatic high beam sensor state past 5 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err

Condition can be displayed*

  • w/ Automatic High Beam System
  • Although the item is displayed on the Techstream, it is not applicable to the vehicle.

Auto H Beam STS6

Automatic high beam sensor state past 6 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err

Condition can be displayed*

  • w/ Automatic High Beam System
  • Although the item is displayed on the Techstream, it is not applicable to the vehicle.

Auto H Beam STS7

Automatic high beam sensor state past 7 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err

Condition can be displayed*

  • w/ Automatic High Beam System
  • Although the item is displayed on the Techstream, it is not applicable to the vehicle.

The Number of DTC

Number of trouble codes / 0 to 255

Number of stored DTCs displayed

 

HINT:

*: The details of each value of the Control Range are as follows:

Range

Condition

Control Condition

Diagnostic Note

Undetec

Automatic high beam sensor being initialized

Control suspended (low beam headlights illuminated)

-

CAM NA

Automatic high beam sensor temporarily disabled due to high temperature, unclear image (due to dirt, fog, etc.), etc.

Control suspended (low beam headlights illuminated)

-

No sens

No lights detected

High beam headlights illuminated

Only when vehicle speed within operation speed range

Hlight

Headlights of oncoming vehicle, etc. detected

Low beam headlights illuminated

Only when vehicle speed within operation speed range

Taillgt

Taillights preceding vehicle, etc. detected

Low beam headlights illuminated

Only when vehicle speed within operation speed range

Speed

No lights detected and vehicle speed below operation speed

Low beam headlights illuminated

-

Daytime

Bright light detected

Low beam headlights illuminated

-

Village

Streetlights, etc. detected

Low beam headlights illuminated

Only when vehicle speed within operation speed range

Delay

Changing between low beams and high beams

Changing between low beams and high beams

Only when vehicle speed within operation speed range

Malfunc

Not applicable

-

-

Aim Lmt

SAE Mod

Undefin

LIN Err

Combination Meter

Tester Display

Measurement Item

Control Range

Diagnostic Note

Turn Signal Switch (Right)

Turn signal switch (right) signal / OFF or ON

OFF: Turn signal switch (right) off

ON: Turn signal switch (right) on

-

Turn Signal Switch (Left)

Turn signal switch (left) signal / OFF or ON

OFF: Turn signal switch (left) off

ON: Turn signal switch (left) on

-

Hazard Flasher Switch

Hazard warning signal switch / OFF or ON

OFF: Hazard warning signal switch off

ON: Hazard warning signal switch on

-

Turn Switch Signal (Full Turn)

Turn signal switch signal / OFF or ON

OFF: Turn signal switch off

OFF: Turn signal switch on (Full Turn)

Displays for both right and left turns.

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn the Techstream on.

(e) Enter the following menus:

(1) Body Electrical / Main Body / Active Test.

(2) Body Electrical / Combination Meter / Active Test.

(3) Body Electrical / Mirror L / Active Test.

(4) Body Electrical / Mirror R / Active Test.

(f) Perform the Active Test according to the display on the Techstream.

Main Body

Tester Display

Measurement Item

Normal Condition

Diagnostic Note

Daytime Running Light

No. 1 daytime running relay (DRL)

OFF or ON

-

Illuminated Entry System

Illumination

OFF or ON

Perform the Active Test when DOOR switch in the interior dome light switch assembly, roof console box assembly (front interior light) and No. 1 room light assembly (rear interior light) turned on.

Cargo Light

Cargo light

OFF or ON

Deck light switch assembly is DOOR or on

Taillight Relay

Taillight relay (TAIL)

OFF or ON

-

Headlight

Headlight relay (H-LP)

OFF or ON

-

Head Light Hi

Headlight dimmer relay (DIMMER)

OFF or ON

-

Front Fog Light Relay

Front fog light relay (FOG)

OFF or ON

w/ Fog Light

Relay for Interior Light Auto Cut Function

DOME relay (DOME)

OFF or ON

ON: DOME CUT relay off (interior lights turn off)

OFF: DOME CUT relay on (interior lights turn on)

Combination Meter

Tester Display

Measurement Item

Control Range

Diagnostic Note

Automatic High Beam Indicator

Automatic high beam indicator light

OFF or ON

w/ Automatic High Beam System

Mirror L

Tester Display

Test Part

Control Range

Diagnostic Note

Fr Foot Light

Outer rear view mirror assembly LH (footwell light LH)

OFF or ON

w/ Door Mirror Foot Light

Mirror R

Tester Display

Test Part

Control Range

Diagnostic Note

Fr Foot Light

Outer rear view mirror assembly RH (footwell light RH)

OFF or ON

w/ Door Mirror Foot Light

    Customize Parameters

    Diagnostic Trouble Code Chart

    See More:

    Toyota Tundra Service Manual > Exterior: Fender Liner(for Front Side)
    Components COMPONENTS ILLUSTRATION ILLUSTRATION ILLUSTRATION ILLUSTRATION Installation INSTALLATION PROCEDURE 1. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH (a) for Resin Type Bumper: (1) Install the front wheel opening extension pad LH with the 5 screws. (2) Install the clip. (b) for Steel Type Bu ...

    Toyota Tundra Owners Manual

    Toyota Tundra Service Manual

    © 2024 Copyright www.ttundra.com
    0.0097