Toyota Tundra Service Manual: Vehicle Speed Sensor Circuit (C1AA3)

Toyota Tundra Service Manual / Engine, Hybrid System / Cruise Control / Forward Recognition Camera System / Vehicle Speed Sensor Circuit (C1AA3)

DESCRIPTION

The forward recognition camera receives vehicle speed signals from the skid control ECU (brake actuator assembly). If the skid control ECU (brake actuator assembly) receives a vehicle speed sensor malfunction signal, it informs the forward recognition camera via CAN communication, and DTC C1AA3 is stored.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

C1AA3

Vehicle Speed Sensor Circuit

3 seconds after the ignition switch is turned to ON, a signal from the skid control ECU (brake actuator assembly) indicating a malfunction in a vehicle speed sensor is detected by the forward recognition camera for 5 seconds or more.
  • Vehicle stability control system
  • Skid control ECU (brake actuator assembly)
  • Forward recognition camera

CAUTION / NOTICE / HINT

NOTICE:

  • When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
  • If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Axis Adjustment.

    Click here

  • The forward recognition camera system uses the CAN communication system. First, confirm that there are no malfunctions in the CAN communication system. Refer to How to Proceed with Troubleshooting.

    Click here

PROCEDURE

1.

CHECK FOR DTCs (VEHICLE STABILITY CONTROL SYSTEM)

HINT:

If DTC C1AA3 is stored, the vehicle stability control system may be malfunctioning. Check for DTCs related to the vehicle stability control system first.

(a) Check for DTCs.

Click here

Result

Proceed to

Vehicle stability control system DTCs are not output

A

Vehicle stability control system DTCs are output

B
B

GO TO VEHICLE STABILITY CONTROL SYSTEM

A

2.

CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)

(a) Clear the DTCs.

Click here

(b) Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.

(c) Check for DTCs.

Click here

Result

Proceed to

DTC C1AA3 is not output

A

DTC C1AA3 is output

B
A

USE SIMULATION METHOD TO CHECK

B

3.

REPLACE FORWARD RECOGNITION CAMERA

(a) Replace the forward recognition camera.

Click here

(b) Perform forward recognition camera axis adjustment.

Click here

NEXT

4.

CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)

(a) Clear the DTCs.

Click here

(b) Make sure that the DTC detection conditions are met.

HINT:

If the conditions are not met, the system cannot detect the malfunction.

(c) Check for DTCs.

Click here

Result

Proceed to

DTC C1AA3 is not output

A

DTC C1AA3 is output

B
A

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)
B

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

    Vehicle Speed Tolerance Malfunction (C1AA2)

    Yaw Rate Sensor Circuit (C1AA4,C1AA5)

    See More:

    Toyota Tundra Service Manual > Rear View Monitor System(for Radio And Display Type): How To Proceed With Troubleshooting
    CAUTION / NOTICE / HINT HINT: Use these procedures to troubleshoot the rear view monitor system. PROCEDURE 1. VEHICLE BROUGHT TO WORKSHOP NEXT 2. CUSTOMER PROBLEM ANALYSIS NEXT 3. CHECK DTC OF AUDIO AND VISUAL SYSTEM (a) Refer to DTC Check/Clear procedures of the audio and visual system. Click here ...

    Toyota Tundra Owners Manual

    Toyota Tundra Service Manual

    © 2026 Copyright www.ttundra.com
    0.02