DATA LIST / ACTIVE TEST
1. READ DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches,
sensors, actuators and other items to be read without removing any parts. This non-intrusive
inspection can be very useful because intermittent conditions or signals may be
discovered before parts or wiring is disturbed. Reading the Data List information
early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference
values. Do not depend solely on these reference values when deciding whether a part
is faulty or not.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch ON.
(c) Turn the tester on.
(d) Enter the following menus: Body Electrical / (desired system) / Data List.
(e) According to the display on, read the "DATA LIST".
Main Body
|
Tester Display
|
Measurement Item/Range
|
Normal Condition
|
Diagnostic Note
|
|
Mirror Selection SW (R)
|
Mirror master switch signal for RH mirror / ON or OFF
|
ON: Mirror master switch is in R position
OFF: Mirror master switch is OFF or in L position
|
-
|
|
Mirror Selection SW (L)
|
Mirror master switch signal for LH mirror / ON or OFF
|
ON: Mirror master switch is in L position
OFF: Mirror master switch is OFF or in R position
|
-
|
|
Mirror Position SW (R)
|
Mirror control switch signal (RIGHT) / ON or OFF
|
ON: RIGHT switch is ON
OFF: Any switch except RIGHT is ON or all switches are OFF
|
-
|
|
Mirror Position SW (L)
|
Mirror control switch signal (LEFT) / ON or OFF
|
ON: LEFT switch is ON
OFF: Any switch except LEFT is ON or all switches are OFF
|
-
|
|
Mirror Position SW (Up)
|
Mirror control switch signal (Up) / ON or OFF
|
ON: UP switch is ON
OFF: Any switch except UP is ON or all switches are OFF
|
-
|
|
Mirror Position SW (Dwn)
|
Mirror control switch signal (DOWN) / ON or OFF
|
ON: DOWN switch is ON
OFF: Any switch except DOWN is ON or all switches are OFF
|
-
|
|
Outer Mirror Fold SW
|
Mirror retract switch signal / ON or OFF
|
ON: Mirror retract switch is ON (retracting)
OFF: Mirror retract switch is OFF
|
-
|
|
Mem SW NO. w/KeyID1
|
Switch linked with key ID1 / NONE, MEM SW1, MEM SW2 or MEM SW3
|
NONE: No switches linked with key ID1
MEM SW1: M1 linked with key ID1
MEM SW2: M2 linked with key ID1
MEM SW3: M3 linked with key ID1
|
Only item displayed (not supported)
|
|
Mem SW NO. w/KeyID2
|
Switch linked with key ID2 / NONE, MEM SW1, MEM SW2 or MEM SW3
|
NONE: No switches linked with key ID2
MEM SW1: M1 linked with key ID2
MEM SW2: M2 linked with key ID2
MEM SW3: M3 linked with key ID2
|
Only item displayed (not supported)
|
|
Mem SW NO. w/KeyID3
|
Switch linked with key ID3 / NONE, MEM SW1, MEM SW2 or MEM SW3
|
NONE: No switches linked with key ID3
MEM SW1: M1 linked with key ID3
MEM SW2: M2 linked with key ID3
MEM SW3: M3 linked with key ID3
|
Only item displayed (not supported)
|
|
Mem SW NO. w/KeyID4
|
Switch linked with key ID4 / NONE, MEM SW1, MEM SW2 or MEM SW3
|
NONE: No switches linked with key ID4
MEM SW1: M1 linked with key ID4
MEM SW2: M2 linked with key ID4
MEM SW3: M3 linked with key ID4
|
Only item displayed (not supported)
|
|
Mem SW NO. w/KeyID5
|
Switch linked with key ID5 / NONE, MEM SW1, MEM SW2 or MEM SW3
|
NONE: No switches linked with key ID5
MEM SW1: M1 linked with key ID5
MEM SW2: M2 linked with key ID5
MEM SW3: M3 linked with key ID5
|
Only item displayed (not supported)
|
|
Mem SW NO. w/KeyID6
|
Switch linked with key ID6 / NONE, MEM SW1, MEM SW2 or MEM SW3
|
NONE: No switches linked with key ID6
MEM SW1: M1 linked with key ID6
MEM SW2: M2 linked with key ID6
MEM SW3: M3 linked with key ID6
|
Only item displayed (not supported)
|
|
Mem SW NO. w/KeyID7
|
Switch linked with key ID7 / NONE, MEM SW1, MEM SW2 or MEM SW3
|
NONE: No switches linked with key ID7
MEM SW1: M1 linked with key ID7
MEM SW2: M2 linked with key ID7
MEM SW3: M3 linked with key ID7
|
Only item displayed (not supported)
|
Mirror L
|
Tester Display
|
Measurement Item/Range
|
Normal Condition
|
Diagnostic Note
|
|
Seat Memory Switch1
|
Seat memory switch M1 switch signal / OFF or ON
|
OFF: Seat memory switch M1 switch off
ON: Seat memory switch M1 switch on
|
-
|
|
Seat Memory Switch2
|
Seat memory switch M2 switch signal / OFF or ON
|
OFF: Seat memory switch M2 switch off
ON: Seat memory switch M2 switch on
|
-
|
|
Seat Memory Switch3
|
Seat memory switch M3 switch signal / OFF or ON
|
OFF: Seat memory switch M3 switch off
ON: Seat memory switch M3 switch on
|
Only item displayed (not supported)
|
|
Seat Memory Set SW
|
Seat memory switch SET switch signal / OFF or ON
|
OFF: Seat memory switch SET switch off
ON: Seat memory switch SET switch on
|
-
|
|
Mirror Memory No.1
|
Mirror position memorized in memory switch M1 / OFF or ON
|
OFF: Not memorized
ON: Memorized
|
-
|
|
Mirror Memory No.2
|
Mirror position memorized in memory switch M2 / OFF or ON
|
OFF: Not memorized
ON: Memorized
|
-
|
|
Mirror Memory No.3
|
Mirror position memorized in memory switch M3 / OFF or ON
|
OFF: Not memorized
ON: Memorized
|
Only item displayed (not supported)
|
|
Mirror Memory No.4
|
Mirror position memorized in memory switch M4 / OFF or ON
|
OFF: Not memorized
ON: Memorized
|
Only item displayed (not supported)
|
|
Mirror Memory No.5
|
Mirror position memorized in memory switch M5 / OFF or ON
|
OFF: Not memorized
ON: Memorized
|
Only item displayed (not supported)
|
|
Mirror Memory No.6
|
Mirror position memorized in memory switch M6 / OFF or ON
|
OFF: Not memorized
ON: Memorized
|
Only item displayed (not supported)
|
|
Mirror Memory (Rev) No.1
|
Reverse shift-linked mirror position memorized in seat memory switch
1 / OFF or ON
|
OFF: Not memorized
ON: Memorized
|
-
|
|
Mirror Memory (Rev) No.2
|
Reverse shift-linked mirror position memorized in seat memory switch
1 / OFF or ON
|
OFF: Not memorized
ON: Memorized
|
-
|
|
Mirror Memory (Rev) No.3
|
Reverse shift-linked mirror position memorized in seat memory switch
1 / OFF or ON
|
OFF: Not memorized
ON: Memorized
|
Only item displayed (not supported)
|
|
Mirror Vertical Sensor Vol
|
Vertical mirror position / MIN: 0, MAX: 5 V
|
0 to 5 V
|
-
|
|
Mirror Horizontal Sensor Vol
|
Horizontal mirror position / MIN: 0, MAX: 5 V
|
0 to 5 V
|
-
|
|
+B Voltage Input Value
|
Power supply for outer mirror control ECU assembly / MIN: 0 V, MAX: 25.5
V
|
11 to 14 (V)
|
-
|
|
# Codes
|
Number of trouble codes / 0 to 255
|
Number of stored DTCs displayed
|
-
|
Mirror R
|
Tester Display
|
Measurement Item/Range
|
Normal Condition
|
Diagnostic Note
|
|
Seat Memory Switch1
|
Seat memory switch M1 switch signal / OFF or ON
|
OFF: Seat memory switch M1 switch off
ON: Seat memory switch M1 switch on
|
Only item displayed (not supported)
|
|
Seat Memory Switch2
|
Seat memory switch M2 switch signal / OFF or ON
|
OFF: Seat memory switch M2 switch off
ON: Seat memory switch M2 switch on
|
Only item displayed (not supported)
|
|
Seat Memory Switch3
|
Seat memory switch M3 switch signal / OFF or ON
|
OFF: Seat memory switch M3 switch off
ON: Seat memory switch M3 switch on
|
Only item displayed (not supported)
|
|
Seat Memory Set SW
|
Seat memory switch SET switch signal / OFF or ON
|
OFF: Seat memory switch SET switch off
ON: Seat memory switch SET switch on
|
Only item displayed (not supported)
|
|
Mirror Memory No.1
|
Mirror position memorized in memory switch M1 / OFF or ON
|
OFF: Not memorized
ON: Memorized
|
-
|
|
Mirror Memory No.2
|
Mirror position memorized in memory switch M2 / OFF or ON
|
OFF: Not memorized
ON: Memorized
|
-
|
|
Mirror Memory No.3
|
Mirror position memorized in memory switch M3 / OFF or ON
|
OFF: Not memorized
ON: Memorized
|
Only item displayed (not supported)
|
|
Mirror Memory No.4
|
Mirror position memorized in memory switch M4 / OFF or ON
|
OFF: Not memorized
ON: Memorized
|
Only item displayed (not supported)
|
|
Mirror Memory No.5
|
Mirror position memorized in memory switch M5 / OFF or ON
|
OFF: Not memorized
ON: Memorized
|
Only item displayed (not supported)
|
|
Mirror Memory No.6
|
Mirror position memorized in memory switch M6 / OFF or ON
|
OFF: Not memorized
ON: Memorized
|
Only item displayed (not supported)
|
|
Mirror Memory (Rev) No.1
|
Reverse shift-linked mirror position memorized in seat memory switch
1 / OFF or ON
|
OFF: Not memorized
ON: Memorized
|
-
|
|
Mirror Memory (Rev) No.2
|
Reverse shift-linked mirror position memorized in seat memory switch
1 / OF or ON
|
OFF: Not memorized
ON: Memorized
|
-
|
|
Mirror Memory (Rev) No.3
|
Reverse shift-linked mirror position memorized in seat memory switch
1 / OFF or ON
|
OFF: Not memorized
ON: Memorized
|
Only item displayed (not supported)
|
|
Mirror Vertical Sensor Vol
|
Vertical mirror position / MIN: 0, MAX: 5 V
|
0 to 5 V
|
-
|
|
Mirror Horizontal Sensor Vol
|
Horizontal mirror position / MIN: 0, MAX: 5 V
|
0 to 5 V
|
-
|
|
+B Voltage Input Value
|
Power supply for outer mirror control ECU assembly / MIN: 0 V, MAX: 25.5
V
|
11 to 14 V
|
-
|
|
# Codes
|
Number of trouble codes / 0 to 255
|
Number of stored DTCs displayed
|
-
|
2. PERFORM ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and
other items to be operated without removing any parts. This non-intrusive functional
inspection can be very useful because intermittent operation may be discovered before
parts or wiring is disturbed. Performing Active Tests early in troubleshooting is
one way to save diagnostic time. Data List information can be displayed while performing
Active Tests.
(a) Warm up the engine.
(b) Turn the ignition switch OFF.
(c) Connect the the Techstream to the DLC3.
(d) Turn the ignition switch ON (IG).
(e) Turn the on.
(f) Enter the following menus: Body Electrical / (desired system) / Active Test.
(g) According to the display on tester, perform the "ACTIVE TEST".
(h) Techstream
Mirror L
|
Tester Display
|
Measurement Item
|
Control Range
|
Diagnostic Note
|
|
Mirror Up/Down
|
Mirror vertical operation
|
OFF, Down or Up
|
- Operate with ignition switch ON and the vehicle stopped.
- This test tilts the mirror up or down.
- This operation can be confirmed by watching the mirror move in the
desired direction.
|
|
Mirror Right/Left
|
Mirror horizontal operation
|
OFF, Right or Left
|
- Operate with ignition switch ON and the vehicle stopped.
- This test tilts the mirror up or down.
- This operation can be confirmed by watching the mirror move in the
desired direction.
|
|
Mirror Fold/Return
|
Mirror retract/return operation
|
OFF, Fold or Rturn
|
- Operate with ignition switch ON and the vehicle stopped.
- This test tilts the mirror up or down.
- This operation can be confirmed by watching the mirror move in the
desired direction.
|
|
Mirror Heater
|
Mirror heater operation
|
OFF or ON
|
- Operate with ignition switch ON and the vehicle stopped.
- This test turns the mirror heater on or off.
- Mirror heater operation can be confirmed by touch.
|
Mirror R
|
Tester Display
|
Measurement Item
|
Control Range
|
Diagnostic Note
|
|
Mirror Up/Down
|
Mirror vertical operation
|
OFF, Down or Up
|
- Operate with ignition switch ON and the vehicle stopped.
- This test tilts the mirror up or down.
- This operation can be confirmed by watching the mirror move in the
desired direction.
|
|
Mirror Right/Left
|
Mirror horizontal operation
|
OFF, Right or Left
|
- Operate with ignition switch ON and the vehicle stopped.
- This test tilts the mirror up or down.
- This operation can be confirmed by watching the mirror move in the
desired direction.
|
|
Mirror Fold/Return
|
Mirror retract/return operation
|
OFF, Fold or Rturn
|
- Operate with ignition switch ON and the vehicle stopped.
- This test tilts the mirror up or down.
- This operation can be confirmed by watching the mirror move in the
desired direction.
|
|
Mirror Heater
|
Mirror heater operation
|
OFF or ON
|
- Operate with ignition switch ON and the vehicle stopped.
- This test turns the mirror heater on or off.
- Mirror heater operation can be confirmed by touch.
|
|
