Toyota Tundra Service Manual: FCM Destination Information Uninitialized (C1AAA)

Toyota Tundra Service Manual / Engine, Hybrid System / Cruise Control / Lane Departure Alert System / FCM Destination Information Uninitialized (C1AAA)

DESCRIPTION

When the forward recognition camera is replaced with a new one, the new forward recognition camera attempts to store the country specification information received from the main body ECU (multiplex network body ECU). If the forward recognition camera cannot store the country specification information, DTC C1AAA is stored.

DTC No.	Detection Item	DTC Detection Condition	Trouble Area
C1AAA	FCM Destination Information Uninitialized	3 seconds after the ignition switch is turned to ON, the forward recognition camera cannot store the vehicle specification information.	Main body ECU (multiplex network body ECU) Forward recognition camera CAN Communication System

CAUTION / NOTICE / HINT

NOTICE:

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera learning.
Click here

HINT:

This DTC is stored when the country specification information stored in the forward recognition camera and that stored in the main body ECU (multiplex network body ECU) do not match. If the forward recognition camera or main body ECU (multiplex network body ECU) has been replaced, check if a forward recognition camera or main body ECU (multiplex network body ECU) from another vehicle was used.

PROCEDURE

1.	CHECK DTC OUTPUT (CAN COMMUNICATION DTC OUTPUT)

HINT:

The forward recognition camera communicates with the main body ECU (multiplex network body ECU) via CAN communication. Confirm that the CAN communication system is functioning normally before proceeding.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Chassis / LKA/LDA / Trouble Codes.

(e) Check for DTCs.

Result	Proceed to
DTC U0142 is not output	A
DTC U0142 is output	B

GO TO CAN COMMUNICATION SYSTEM

2.	CHECK DTC OUTPUT

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Chassis / LKA/LDA / Trouble Codes.

(e) Clear the DTCs.

(f) Make sure that the DTC detection conditions are met.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

(g) Check for DTCs.

Result	Proceed to
DTC C1AAA is output.	A
DTC C1AAA is not output.	B

USE SIMULATION METHOD TO CHECK

3.	REPLACE FORWARD RECOGNITION CAMERA

(a) Replace the forward recognition camera.

Click here

(b) Adjust the forward recognition camera.

Click here

4.	CHECK DTC OUTPUT

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(d) Enter the following menus: Chassis / LKA/LDA / Trouble Codes.

(e) Clear the DTCs.

(f) Make sure that the DTC detection conditions are met.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

(g) Check for DTCs.

Result	Proceed to
DTC C1AAA is output	A
DTC C1AAA is not output	B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

Front Camera Module Incorrect Axial Gap (C1AA8,C1AA9)

Customize Parameters

See More:

Toyota Tundra Owners Manual > Do-it-yourself maintenance: Wireless remote control battery
Replace the battery with a new one if it is depleted. You will need the following items: Flathead screwdriver Small flathead screwdriver Lithium battery CR2016 Replacing the battery 1. Remove the cover. To prevent damage to the key, cover the tip of the screwdriver with a rag. To prevent the button ...