Toyota Tundra Service Manual: Short in Curtain Shield Airbag (RH) Squib Circuit (B1830-B1833)

Toyota Tundra Service Manual / Vehicle Interior / Supplemental Restraint Systems / Airbag System / Short in Curtain Shield Airbag (RH) Squib Circuit (B1830-B1833)

DESCRIPTION

The curtain shield squib RH circuit consists of the airbag sensor assembly and curtain shield airbag assembly RH.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the curtain shield squib RH circuit.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Warning Indicate

Test Mode / Check Mode

B1830

Short in Curtain Shield Airbag (RH) Squib Circuit

One of the following conditions is met:

  • The airbag sensor assembly detects a line short circuit signal 5 times in the curtain shield squib RH circuit during the primary check.
  • A curtain shield airbag assembly RH malfunction.
  • An airbag sensor assembly malfunction.
  • No. 2 floor wire
  • Curtain shield airbag assembly RH
  • Airbag sensor assembly

Comes on

Applicable

B1831

Open in Curtain Shield Airbag (RH) Squib Circuit

One of the following conditions is met:

  • The airbag sensor assembly detects an open circuit signal in the curtain shield squib RH circuit for 2 seconds.
  • A curtain shield airbag assembly RH malfunction.
  • An airbag sensor assembly malfunction.
  • No. 2 floor wire
  • Curtain shield airbag assembly RH
  • Airbag sensor assembly

Comes on

Applicable

B1832

Short in Curtain Shield Airbag (RH) Squib Circuit (to Ground)

One of the following conditions is met:

  • The airbag sensor assembly detects a short circuit to ground signal in the curtain shield squib RH circuit for 0.5 seconds.
  • A curtain shield airbag assembly RH malfunction.
  • An airbag sensor assembly malfunction.
  • No. 2 floor wire
  • Curtain shield airbag assembly RH
  • Airbag sensor assembly

Comes on

Applicable

B1833

Short in Curtain Shield Airbag (RH) Squib Circuit (to +B)

One of the following conditions is met:

  • The airbag sensor assembly detects a short circuit to B+ signal in the curtain shield squib RH circuit for 0.5 seconds.
  • A curtain shield airbag assembly RH malfunction.
  • An airbag sensor assembly malfunction.
  • No. 2 floor wire
  • Curtain shield airbag assembly RH
  • Airbag sensor assembly

Comes on

Applicable

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

    Click here

HINT:

To perform the simulation method, enter check mode (signal check) with the Techstream (Click here ), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here ).

PROCEDURE

1.

CHECK CONNECTORS

(a) Turn the ignition switch off.

*1

Curtain Shield Airbag Assembly RH

*2

Airbag Sensor Assembly

*3

No. 2 Floor Wire

(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Check that the connectors are properly connected to the curtain shield airbag assembly RH and airbag sensor assembly.

OK:

The connectors are properly connected.

HINT:

If the connectors are not properly connected, reconnect the connectors and proceed to the next inspection.

(d) Disconnect the connectors from the curtain shield airbag assembly RH and airbag sensor assembly.

(e) Check that the terminals of the connectors are not deformed or damaged.

OK:

The terminals are not deformed or damaged.

(f) Check that the short springs of the activation prevention mechanism of the No. 2 floor wire connector are not deformed or damaged.

OK:

The short springs are not deformed or damaged.

NG

REPLACE NO. 2 FLOOR WIRE

OK

2.

CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH

(a) Connect the connector to the airbag sensor assembly.

*1

Curtain Shield Airbag Assembly RH

*2

Airbag Sensor Assembly

*3

SST

*a

Front view of wire harness connector

(to Curtain Shield Airbag Assembly RH)

(b) Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the curtain shield airbag assembly RH for measurement, as this may lead to a serious injury due to airbag deployment.

NOTICE:

  • Do not forcibly insert SST into the terminals of the connector when connecting SST.
  • Insert SST straight into the terminals of the connector.

SST: 09843-18061

(c) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

(d) Turn the ignition switch to ON, and wait for at least 60 seconds.

(e) Clear the DTCs.

Click here

(f) Turn the ignition switch off.

(g) Turn the ignition switch to ON, and wait for at least 60 seconds.

(h) Check for DTCs.

Click here

Result

Proceed to

DTC B1830, B1831, B1832 or B1833 is not output

A

DTC B1830, B1831, B1832 or B1833 is output

B

HINT:

Codes other than DTC B1830, B1831, B1832 and B1833 may be output at this time, but they are not related to this check.

(i) Turn the ignition switch off.

(j) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(k) Disconnect SST from connector C.

A

REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY RH

B

3.

CHECK NO. 2 FLOOR WIRE

(a) Disconnect the No. 2 floor wire from the airbag sensor assembly.

*1

Curtain Shield Airbag Assembly RH

*2

Airbag Sensor Assembly

*3

No.2 Floor Wire

*a

Front view of wire harness connector

(to Curtain Shield Airbag Assembly RH)

Release the activation prevention mechanism

(b) Check for a short to B+ in the circuit.

(1) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

(2) Turn the ignition switch to ON.

(3) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

Q3-2 (ICR+) - Body ground

Ignition switch ON

Below 1 V

Q3-1 (ICR-) - Body ground

Ignition switch ON

Below 1 V

(4) Turn the ignition switch off.

(5) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Check for an open in the circuit.

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Q3-2 (ICR+) - Q3-1 (ICR-)

Always

Below 1 Ω

(d) Check for a short to ground in the circuit.

(1) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Q3-2 (ICR+) - Body ground

Always

1 MΩ or higher

Q3-1 (ICR-) - Body ground

Always

1 MΩ or higher

(e) Check for a short in the circuit.

(1) Release the activation prevention mechanism built into connector B.

Click here

(2) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

Q3-2 (ICR+) - Q3-1 (ICR-)

Always

1 MΩ or higher

(3) Restore the released activation prevention mechanism of connector B to the original condition.

NG

REPLACE NO. 2 FLOOR WIRE

OK

4.

CHECK DTC

(a) Connect the connectors to the curtain shield airbag assembly RH and airbag sensor assembly.

*1

Curtain Shield Airbag Assembly RH

*2

Airbag Sensor Assembly

(b) Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

(c) Turn the ignition switch to ON, and wait for at least 60 seconds.

(d) Clear the DTCs.

Click here

(e) Turn the ignition switch off.

(f) Turn the ignition switch to ON, and wait for at least 60 seconds.

(g) Check for DTCs.

Click here

Result

Proceed to

DTC B1830, B1831, B1832 or B1833 is not output

A

DTC B1830, B1831, B1832 or B1833 is output

B

HINT:

Codes other than DTC B1830, B1831, B1832 and B1833 may be output at this time, but they are not related to this check.

A

USE SIMULATION METHOD TO CHECK

B

REPLACE AIRBAG SENSOR ASSEMBLY

    Short in Side Squib (LH) Circuit (B1825-B1828)

    Short in Curtain Shield Airbag (LH) Squib Circuit (B1835-B1838)

    See More:

    Toyota Tundra Service Manual > Front Seat Inner Belt Assembly(for Center Seat): Removal
    REMOVAL PROCEDURE 1. REMOVE FRONT SEAT ASSEMBLY LH (a) for Power Seat: Remove the front seat (see page ). (b) for Manual Seat: Remove the front seat (see page ). 2. REMOVE FRONT SEAT ASSEMBLY RH (a) for Power Seat: Remove the front seat (see page ). (b) for Manual Seat: Remove the front seat (see pa ...

    Toyota Tundra Owners Manual

    Toyota Tundra Service Manual

    © 2024 Copyright www.ttundra.com
    0.0326